Essential Plumber Guide for Installing a Bathtub
Essential Plumber Guide for Installing a Bathtub
Blog Article
We have noticed the article relating to Installing A Bathtub below on the internet and decided it made sense to relate it with you over here.
Installing a bathtub isn't exactly rocket science, however it does call for solid plumbing, carpentry, as well as in some cases, tiling abilities. Changing an old tub with a brand-new one is likewise a reasonably tough task. If the old bathtub is readily obtainable, the project can move immediately; if you have to open up a wall surface to get rid of the old tub and also place the brand-new bath tub, the task is much harder. In either situation, the task is within a house handyman's skills, although you will certainly require a helper to vacate the old bathtub and set in the brand-new one. Make certain you have certified yourself for the job as well as fit trying it. Rather than hiring a service provider to take control of a halfway-completed project, it is far better to think about utilizing one prior to you start. Opportunities are you might need a professional plumber to make tube connections.
This post will certainly help you mount a new bath tub in your restroom if you have actually currently acquired a brand-new bathtub as well as don't require to transform the arrangement of your previous water pipelines.
Your devices as well as product list ought to comprise the following:
Removing Old Taps
If you need to change old taps with new ones as a part of your installation, then the first thing you must do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any type of water continuing to be in the system. The process of eliminating the existing taps can be quite problematic because of the limited access that is frequently the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the faucets. Have a cloth all set for the staying water that will originate from the pipelines. Once the supply pipes have actually been removed, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the single taps from turning during this process. When the faucets have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old securing compound.
Prior to going on to fit the brand-new taps, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will require a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap and also the other end offers a connection to the existing supply pipes.
If you need to fit a monobloc, then you will need decreasing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin making sure that the washing machines remain in place between the faucet and the sink. Secure the faucet in position with the supplier given backnut. When the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet ports. The previous type needs to be attached to the tap ends first, tightening up only by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Installing the Tub
Making use of the two wood boards under its feet, position the tub in the needed setting. The wood boards are practical in uniformly spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto four little factors.
The following objective is to ensure that the bath tub is leveled all round. This can be accomplished by checking the spirit level and changing the feet on the tub till the level reads degree.
To install faucets, fit the bottom of the furthest versatile faucet adapter to the appropriate supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Switch on the water and also inspect all joints as well as new pipework for leakages and also tighten them if essential. Fill up the bathtub and likewise examine the overflow electrical outlet as well as the regular outlet for leakages.
Lastly, take care of the bath paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bathtub needs to wait until the tub has been utilized at the very least when as this will resolve it into its final placement.
Preparing for the Installation
To start with, the sustaining frame supplied with the bath ought to be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is very important to make sure that if the tap features a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps unit to avoid strain on the bathtub.
Fit the flexible faucet ports to the bottom of both taps using 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet via the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath must currently be ready to be suited its last position.
Tiling Around the Bathtub
In the area where the bathroom fulfills the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to crack a stiff seal, triggering the water to penetrate the wall between the bath and the tiling, bring about issues with dampness as well as possible leakages to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your components and also fittings. They are offered in tubes and cartridges, as well as can securing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to always fill up the bath tub with water prior to securing, to permit the movement experienced when the tub is in usage. The sealant can break rather very early if you do not take into consideration this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise easily readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing waterproof or water-proof adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am very occupied with How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I'm hoping you enjoyed reading our post. Remember to set aside a second to promote this entry if you liked it. I praise you for your time. Kindly pay a visit to our website back soon.
Immediate attention? Phone us! Report this page